C2 Remove - 3.5L
C2 Remove 3.5 Litres
SKU:C2R-3.5
- Order by 2pm for Same Day Dispatch
Product Information
Easy-to-use C2 Remove preps concrete floors for hardening and densifying or other penetrating protective treatments, as well as grinding and polishing. The low-odor cleaner quickly removes a variety of waxes and acrylics, including most lower-solids cure and seals, from concrete floors. That leaves the concrete free of old coatings that can block treatments from penetrating or clog up the heads on grinding and polishing
equipment. Water-rinsable C2 Remove can be used in concentrate, or diluted with fresh water, depending on the job.
Advantages
- Removes waxes, acrylics and most low-solids
- Cure & seals from concrete floors.
- Low odor for interior use.
- Does not affect concrete color.
- Contains readily biodegradable materials.
Limitations
- Surfaces are slippery during application. Use appropriate caution.
- Product efficiency is reduced in cold temperatures.
- May damage synthetic or reflective glass.
Typical Technical Data
FORM Colorless liquid
SPECIFIC GRAVITY 1.05
pH not applicable
WT/GAL 8.76 lbs
ACTIVE CONTENT not applicable
TOTAL SOLIDS not applicable
VOC CONTENT 4% maximum
FLASH POINT >93°C (200°F) ASTM D3278
FREEZE POINT not applicable
SHELF LIFE 2 years in tightly sealed,unopened container
Safety Information
Always read full label and SDS for precautionary instructions before use. Use appropriate safety equipment and job site controls during application and handling.
Preparation
Protect people, vehicles, property, painted surfaces, plants and all surfaces not set for cleaning from product, splash and wind drift. Protect and/or divert pedestrian and auto traffic. Some metal finishes and glass installed in recent years may be damaged by product. Test or protect if needed.
Surface & Air Temperatures
Cleaning effectiveness is reduced when surface andair temperatures fall below 10°C (50°F).Do not apply at temperatures below 4°C (40°F). If freezing conditions exist prior to application, let concrete thaw.
Equipment
Apply with a long-handled brush or mop and pump-up sprayer. Use a brush or scrubbing machine for light scrubbing. Use a mop or wet vacuum as needed to take up the spent cleaner and debonded coating. Pressure-wash (under 1,000 psi; 7 MPa) or mop with
fresh water only if needed to remove excess residue.
Storage & Handling
Store in a cool, dry place. Always seal container after dispensing. Do not alter or mix with other chemicals.Published shelf life assumes upright storage of factory-sealed containers in a dry place. Maintain temperatures of 7?38°C (45?100°). Do not double stack pallets. Dispose of unused product and container in accordance with local regulations.
Packaging
3.5L, or 20L containers
ALWAYS TEST a small area of each surface to confirm
suitability, coverage rate and desired results before
beginning overall application. Test with the same
equipment, recommended surface preparation and
application procedures planned for general
application. Let surface dry thoroughly before
inspection.
Dilution & Mixing
Dilute with clean water.
Light Wax Build-up:
1 part product to 10 parts water
Heavy Wax Build-up:
1 part product to 3 parts water
Low-Solids Cure & Seals:
Full strength
Coverage Rates
Coverage varies based on concrete porosity and
texture. Always test.
,7.5,12.5 m2/ liter
,300,500 ft2/ US gallon
Application Instructions
1. Apply with low-pressure spray.
2. Allow to dwell for 5-10 minutes.
3. Scrub with a stiff bristle brush or a mechanical scrub machine.
4. Take up as much spent cleaner and dissolved coating as possible.
5. Rinse or mop the floor with fresh water, if needed.
Cleanup. Clean tools and equipment with fresh water.
Best Practices
Allow more dwell time for C2 Remove in temperatures below 10°C (50°F). In rare instances where floors are exposed to freezing temperatures, make sure the concrete is thawed out and surface temperature is above 4°C (40°F).
All loose construction debris and foreign materials from surfaces to be treated must be removed using a dry broom. For oily spot cleaning, use C2 Stain Clean.
Make sure cleaned floors are free as possible of spent cleaner and debonded coatings. A thorough mop, wet-vac or machine scrub usually gets up enough residue so the cleaned floor can be treated, once dry.
Surfaces are slippery during application. Use appropriate caution. If needed, mop or pressure-rinse the cleaned floor with fresh water to flush away excess.